The general rule of thumb is to mount the transducer to the starboard side, which is the down stroke of most single outboard boat propellers (right hand lower unit). This side produces the least amount of turbulence and is most efficient in delivering the best performance.
Table of Contents
Do you need a different transducer for ice fishing?
A special transducer is not necessary. Assuming you can safely remove your boat’s transducer and wiring without damage, it should work fine for ice fishing.
How far should a transducer be in the water ice fishing?
First, hang your transducer roughly 1 ft beneath the ice in your hole. Next, turn the unit on by twisting the range to its first depth. This depth is typically 20 ft.
Where do you put the transducer for ice fishing?
Can a transducer shoot through ice?
Don’t worry about ruining the transducer. Shooting through the ice will not damage the transducer so go ahead and try it a few times. Just wet the ice and try a reading, if you can’t find the bottom, squirt more water and try again.
What depth should I ice fish?
In my experience, I’ve found that most of the best ice-fishing action comes in water from 3-to-20 feet deep. I like to set up my traps so that they cover a variety of depths. Areas with rock piles, weed beds, or dramatic contours are all good spots.
How do you set up a fishfinder for ice fishing?
How deep do you put in the ice transducer?
Set the unit down on the table and hang the Ice-Ducer about 30″ over the floor. Turn on the FL-8, then turn up the gain until you can see your floor as a red signal. THE DEPTH WILL NOT BE ACCURATE WHEN OPERATING IN THE AIR. We are interested in sensitivity only.
How do you mount a transducer for ice fishing?
How deep in the water does a transducer need to be?
Tip # 3 Waterline Thirdly the best bet when mounting your transducer to read at speed is to have the bottom of it 3-4 mm below the waterline. Because the transducer can only ping in water so you do want it submerged. If it’s too deep sometimes the front face of it will create turbulence and bubbles = bad.
What is an ice fishing transducer?
Ice fishing is a stationary form of angling where the transducer – the part of the fish finder that beams the signal down and catches it coming up – is hanging down in the hole. Because of this stationary controlled setting, flasher-style depth finders with an analog signal are extremely popular with ice anglers.
What is needed for ice fishing?
Jigging ice fishing rod and reel. Live bait container stocked with live bait. Terminal tackle such as line clippers, fish grabbers, pliers, hooks, sinkers, etc. Ice fishing tip ups.
Do I need a fish finder for ice fishing?
Ice Fishing Even more importantly, you will see fish react to your bait and be able to dial in your presentation based on what you are gathering. But fish finders and ice flashers are not needed for ice fishing.
Can you turn transducer sideways?
any rocking of the boat beam to beam will not overly affect the transducer signal…the cone “sway” or shift from side to side is minimal. But if you mount a transducer on the horizontal.. any movement beam to beam has a greater affect on the cone “sway”.
What’s the best bait for ice fishing?
For ice fishing live bait, try wax worms (bee moth larva), maggots, spikes (fly larvae), wigglers (mayfly larvae) or minnows. You can drop your bait and leave it alone, or you can slowly jig to attract the fish. Ice fishing jigging also works with artificial ice fishing bait.
What is the best month to ice fish?
March is my favorite month for ice-fishing. The days are longer, the weather isn’t as cold, and the fish like to get caught in March. Following are some things to keep in mind to catch more fish through the ice until the end of the ice season.
How many pounds can 4 inches of ice hold?
Ice is not considered safe to walk on until it is at least 4 inches thick. At 4″ the ice is suitable for ice fishing, cross-country skiing and walking and can support about 200 pounds. At 5 inches of new clear ice should be enough to hold a single snowmobile or ATV or about 800 pounds.
How do you read a fishfinder ice fishing?
What is flasher mode on a fish finder?
The use of a flasher-style display uses a rotating wheel that displays the bottom and other targets in a series of lights on that spinning wheel. In contrast to liquid-crystal displays that show a history of what your boat has passed over, a spinning-wheel flasher displays the bottom and targets in real time.
What do fish look like on vexilar?
How do fish finder find fish?
Does Lowrance hook2 have flasher mode?
Can you use a Lowrance HDS 7 for ice fishing?
A Portable Power Pack (SKU: 000-15111-001) is required to use the LiveSight Ice Transducer with HDS LIVE 7 or HDS Carbon 7 displays. HDS Carbon displays also require the compact, PSI-1 module to work with the LiveSight Sonar transducer.
What happens if transducer is too low?
A transducer placed too low in the water will cause water to flow over the top of the transducer creating a rooster tail and creating air bubbles that will travel over the bottom of the transducer.
What angle should my transducer be at?
The transducer should be mounted nose-up about three degrees in relation to the plane of the hull bottom. Sometimes a transducer mounted parallel with the hull bottom also works fine, but even the slightest nose-down angle can cause turbulence or cavitation that kills performance.