Table of Contents
What degree ice Ducer is best?
The 9-degree (TB0051), also known as the Pro-View Ice-Ducer, delivers the best target ID and is great for all depth applications. It is also very good at limiting interference from other sonar systems.
What is the best ice fishing fish locator?
- Best Overall: Garmin LiveScope Ice Bundle LI.
- Best Budget Ice Fishing Sonar: Vexilar FL-8SE “Genz Pack
- Best Ice Fishing Underwater Camera: Aqua-Vu QUAD HD.
- Best Digital Ice Sonar: MarCum LX-7L.
- Best Portable: Aqua-Vu Micro Revolution Pro 5.0.
- Best Combo Sonar/GPS: Humminbird Ice Helix 7 CHIRP G4.
What does a fish look like on a vexilar?
What angle do you set a transducer?
The transducer should be mounted nose-up about three degrees in relation to the plane of the hull bottom. Sometimes a transducer mounted parallel with the hull bottom also works fine, but even the slightest nose-down angle can cause turbulence or cavitation that kills performance.
How much area does a transducer cover?
Easiest to remember is about 1 ft coverage for every 3 ft of depth with a 19/20 degree transducer, with a 10 degree of course would be half of that.
What’s the best vexilar?
Vexilar GP1812 FL18 Genz Pack 12 Degree Ice-Ducer Combo This one has been around for decades with slight modifications every few years but it continues to be the go-to standard for most people. This is because it offers a 12-degree cone with variable water depth at six different ranges.
What is the difference between a fish finder and a flasher?
The main difference between a fish finder and a flasher is the way that sonar signals are displayed. A flasher shows real-time sonar data from the water column right underneath the ice hole, while a fish finder shows historical sonar data of the last few minutes.
Do I need a fish finder for ice fishing?
Ice Fishing Even more importantly, you will see fish react to your bait and be able to dial in your presentation based on what you are gathering. But fish finders and ice flashers are not needed for ice fishing.
Can you bring a Vexilar on a plane?
I flew last March Milwaukee to Denver with a vexilar. Carry on! I called TSA in advance of the flight and there was no issue. They recommended having it in plain view and separate it from your other carry on items.
Can you use a Vexilar in summer?
Re: Do you use your Vexilar in the summer? Yes. Just buy the transducer for your boat 99.00 bucks works great!
Can you use an ice fishing transducer in open water?
Get an Open Water Kit. They come with either the High Speed or Puck style transducers, the unit and transducer mounting brackets, and a power cord with fuse and terminals. Install the Open Water Kit and leave your ice fishing kit intact. Simply move your flasher from the ice kit to your boat when the ice goes away.
How far should a transducer be in the water ice fishing?
First, hang your transducer roughly 1 ft beneath the ice in your hole. Next, turn the unit on by twisting the range to its first depth. This depth is typically 20 ft.
How do you check Vexilar depth?
For example, on a FL8, start with turning the range knob left to #1. This will show depth 0 to 20 feet, #2 will show depth 0 to 40 feet and #4 is 0 to 80 feet. Turning the knob right is for deeper water: #1 is 0 to 30 feet, #2 is 0 to 60 feet and #4 is 0 to 120 feet.
How do you read a Vexilar ice fishing?
What happens if transducer is too low?
A transducer placed too low in the water will cause water to flow over the top of the transducer creating a rooster tail and creating air bubbles that will travel over the bottom of the transducer.
How far should a transducer be in the water?
The transducer should be even with the bottom of the boat or slightly below the bottom. Leading edge (the edge closest to the transom of the boat). One click too high: the transducer is tilted out of the water and cannot maintain a sonar signal.
Which way do I point my transducer?
The general rule of thumb is to mount the transducer to the starboard side, which is the down stroke of most single outboard boat propellers (right hand lower unit). This side produces the least amount of turbulence and is most efficient in delivering the best performance.
What kHz Should I Use on fish finder?
Frequencies commonly used by a conventional fish finder for recreational boat are 50 kHz (low frequency) and 200 kHz (high frequency). A lower frequency has a wider search angle and area. Generally, the searchable angle of 50 kHz beams is approximately 50 degrees and that of 200 kHz beams is approximately 15 degrees.
How wide is the cone on a fish finder?
The formula is 2 x Depth x tan(Beam Angle/2). I know this is a lot of math, therefore, the rule of thumb for a 60 degree angle is the coverage area equals the depth you are fishing. Hence, if you are fishing in 30 feet of water, the base of that sonar cone will be 30 feet across.
What area does a fish finder cover?
As a rule of thumb, the bottom coverage is about one-third the depth. In other words, if you are sitting in 20 feet of water the fish finder will cover a six-foot circle of the bottom under the boat.
What is a Vexilar fish finder?
The classic Vexilar flasher is truly legendary. The world’s most popular three‑color sonar flasher, the FL‑8se is still one of the best all-around flasher/sonar designs. The hallmark three‑color display shows weak targets in green, medium strength targets in orange and strong bottom targets in red.
How do you read a Vexilar FLX 28?
How do you use a Vexilar FLX 12?
Do you need an ice transducer?
Do you need a special transducer. A special transducer is not necessary. Assuming you can safely remove your boat’s transducer and wiring without damage, it should work fine for ice fishing. Keep in mind that the function of a transducer depends on being level to the surface of the water.